Temperature Monitors and
PWM Fan Controllers
_______________________________________________________________________________________   7
Figure 1. SMBus Protocols
Write Byte Format
Read Byte Format
Send Byte Format
Receive Byte Format
Slave Address: equiva-
lent to chip-select line of
a 3-wire interface
Command Byte: selects which
register you are writing to
Data Byte: data goes into the register
set by the command byte (to set
thresholds, configuration masks, and
sampling rate)
Slave Address: equiva-
lent to chip-select line
Command Byte: selects
which register you are
reading from
Slave Address: repeated
due to change in data-
flow direction
Data Byte: reads from
the register set by the
command byte
Data Byte: writes data to the
register commanded by the
last read byte or write byte
transmission
Data Byte: reads data from
the register commanded
by the last read byte or
write byte transmission;
also used for SMBus alert
response return address
S = Start condition
P = Stop condition
Shaded = Slave transmission
/ / / = Not acknowledged
ACK
7 bits
ADDRESS
ACK
8 bits
DATA
ACK
P
8 bits
S
COMMAND
WR
ACK
7 bits
ADDRESS
ACK
S
ACK
8 bits
DATA
7 bits
ADDRESS
RD
8 bits
P
S
COMMAND
/ / /
WR
ACK
7 bits
ADDRESS
8 bits
COMMAND
ACK
P
S
WR
ACK
7 bits
ADDRESS
RD
8 bits
DATA
P
S
/ / /
Figure 2. SMBus Write Timing Diagram
SMBCLK
A
B
C
D
E   F
G
H
I   J
K
SMBDATA
t
SU:STA
t
HD:STA
t
LOW
t
HIGH
t
SU:DAT
t
HD:DAT
t
SU:STO
t
BUF
A = START CONDITION
B = MSB OF ADDRESS CLOCKED INTO SLAVE
C = LSB OF ADDRESS CLOCKED INTO SLAVE
D = R/W BIT CLOCKED INTO SLAVE
E = SLAVE PULLS SMBDATA LINE LOW
L
M
F = ACKNOWLEDGE BIT CLOCKED INTO MASTER
G = MSB OF DATA CLOCKED INTO SLAVE
H = LSB OF DATA CLOCKED INTO SLAVE
I = MASTER PULLS DATA LINE LOW
J = ACKNOWLEDGE CLOCKED INTO SLAVE
K = ACKNOWLEDGE CLOCK PULSE
L = STOP CONDITION, DATA EXECUTED BY SLAVE
M = NEW START CONDITION
相关PDF资料
MAX6665ASA45+ IC FAN CNTRL/DRVR 8-SOIC
MAX6670AUB45+ IC TEMP SENSOR REMOTE 10-UMAX
MAX6678AEP92+ IC TEMP MONITOR 2CH PWM 20-QSOP
MAX6681MEE+ IC TEMP SENSOR SMBUS 16-QSOP
MAX6689UP34+ IC 7CH PREC TEMP MONITOR 20TSSOP
MAX6690MEE+ IC TEMP SENSOR SMBUS 16-QSOP
MAX6692YMSA+ IC SENSOR REMOTE SMBUS 8SOIC
MAX6693UP9A+T IC TEMP MONITOR 7CH 20-TSSOP
相关代理商/技术参数
MAX6664AEE-T 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
MAX6664AEE-TG075 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX6665ASA070 制造商:Maxim Integrated Products 功能描述:
MAX6665ASA40 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MAX6665ASA40+ 功能描述:马达/运动/点火控制器和驱动器 Fan Controller Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MAX6665ASA40+T 功能描述:马达/运动/点火控制器和驱动器 Fan Controller Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MAX6665ASA40-T 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MAX6665ASA45 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube